PIPE INSULATION

WALL INSULATION

ROOF INSULATION

FLOOR INSULATION

VidoGlue

VidoGlue

Videoglue is a Polychloroprene contact cement designed specifically for hand lasting of leather uppers to insole boards. It is yellow / amber in colour and is brushable thick in consistency. It has an excellent heat-resistance coupled with high initial bond strength. These two properties ensure excellent performance during heat-setting of freshly lasted uppers. The ingredients used in this product are scheduled under REACH (EC) No 1907/2006 wherein the product is described as a “mixture”.

 

 

Technical Data

Vidoglue is brush applied to both upper and insole board. The lasting margin should be minimum of 10mm. After a suitable drying period (15 – 20 minutes) uppers may be lasted by hand. Heat setting at maximum 130°C may follow if required.

Base: Polychloroprene rubber / resin
Colour: Amber / yellow
Viscosity: ± 3 500 cPs
Mass Per Litre: ± 0,8kg
Soilds Content: ± 25%
Flash Point: – 20˚C therefore highly flammable
Open Time: ± 2 hours
Shelf Life: 12 months
Packing: 25 lt and 200 lt containers

A solvent mixture giving a heavy vapour. Not to be used in confined areas without adequate ventilation.
Not to be exposed near a naked flame. Avoid prolonged breathing in of vapour and contact with skin.

  • General information: in case of doubt, or when symptoms persist, seek medical attention. Never give anything by mouth to an unconscious person.
  • Inhalation: remove the patient to fresh air.
  • Skin contact: wash thoroughly with clean water. A skin cleaner may be used. Do NOT use solvents or thinners.
  • Eye contact: contact lenses should be removed. Irrigate copiously with clean, fresh water for at least 10 minutes holding the eyelids apart, seek med. advice.
  • Ingestion: if accidentally swallowed, obtain immediate medical attention. Do NOT induce vomiting. The main hazard is aspiration into the lungs. Obtain medical advice.
  • Personal measures of attention: avoid skin contact.
  • Protection of the environment: the product is a liquid. It contains dangerous components. Collect spillages for disposal according to the waste regulations.
  • Procedure of cleaning and removing: contain and collect the product in mechanical way. Do not dispose in sewers. Contain spillage with sand.
  • Clean preferably with a detergent, avoid the use of solvents

Indication for secure handling: FLAMMABLE containers

 

Indication for fire/explosion-protection: Store according to the requirements of SABS 089:1985

Indication for secure handling: FLAMMABLE containers

 

Indication for fire/explosion-protection: Store according to the requirements of SABS 089:1985

  • State: liquid
  • Colour: amber
  • Smell: Characteristic hydrocarbon

 

Value Unit Method
Flash point 20 ˚C Abel closed cup IP170
Viscosity at 25˚ Liquid 2400 CP Brookfield
Density at 25°C 0,81 g/ml DIN 51 757/C
Lower explosion limit 0,6 vol %
Upper explosion limit 8,0 vol %
Point of ignition 240 ˚C ASTM D2155
Solubility in water immiscible
Content of solvents 75,00%
Vapour pressure @ 20°C 55 mbar
Boiling point 67-77 °C
Conditions: Stable under recommended storage and handling conditions.
Conditions and substances to avoid: Avoid high temperatures (above 35°C). Don’t bring in to contact with oxidizing agents or strong alkaline, acidic or oxidizing materials.
Dangerous substances of decomposition: In a fire hazardous decomposition product such as smoke, CO2, CO may be produced.
Demands for spaces of storage and vessels: Store in a dry, well ventilated place, away from heat and direct sunlight at temp not above 35 °C and away from sparks.
Storage information together with other products: Store separately from strong oxidizing agents and strong alkaline and acidic materials.
More information on conditions of storage: Store only in containers of origin. (or containers which are similar). Observe the label precautions. Store in a dry, well ventilated place not above 30°C, protected against heat and direct sunlight.
Storage Class: Class 1 Division 1a.

Technical safety measures: Provide adequate ventilation. This may be achieved by local or general exhaust ventilation. If these are not sufficient to maintain solvent-vapor-conc. below the exposure limits, suitable respiratory protective equipment has to be worn.

 

Components with limits to be controlled:

Name of substance TLV(mg/m3) (ppm) STEL (mg/m3)
SBP 50/115 (Benzine) 500 1000
MEK 200 150

 

Personal Protection

  • Respirator: Provide respiratory protection.
  • Hand protection: Wear gloves, advice should be sought from glove suppliers. Barrier creams may help to protect exposed areas of the skin (They are not substitutes for physical protection, don’t apply them after exposure).
  • Eye protection: Eye protection to protect against liquid splashes should be worn.
  • Skin protection: Suitable working overall.

The inhalation of the vapours of the preparation may cause hazards to the health. (Irritation of mucous membrane, the respiratory system, damages of kidney and liver, adverse effects on the central nervous system).

The product is a liquid and classified dangerous. There is no data available on polluting the environment.

Product: Do not allow entering drains/water courses or ground water.
Key of disposal: 57110
Name of disp: Wastes of glues (Waste, including containers are controlled wastes and should be disposed in accordance to the Control of Pollution Act / Environment Protecting Act.)
Uncleaned packing: eventually dispose in the recycling
  • R 10 Flammable.
  • R 11 Highly Flammable.
  • R 18 In use, may form inflammable / explosive vapour-air mixture.
  • R 20 Harmful by inhalation.
  • R 36/37/38 Irritating to eyes, respiratory system and skin.
  • R 42 May cause sensitization by inhalation.
  • R 50/53 Toxic to aquatic Organisms, may cause long term adverse effects.
  • R 67 Vapors may cause drowsiness and dizziness.
  • S 2 Keep out of reach of children.
  • S 16 Keep away from sources of ignition.
  • S 25 Avoid contact with eyes.
  • S 26 In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice.
  • S 28 After contact with skin wash immediately with plenty of detergents and water.
  • S 38 In case of insufficient ventilation wear suitable respiratory equipment.
  • S 45 In case of accident or if you feel unwell, seek medical advice immediately, (show the label when possible).
  • S 46 If swallowed, seek medical advice, and show the practitioner this document.

Sea

  • CLASS – 3.1 Pack Group – 2 Symbol – FLAMMABLE LIQUID
  • SHIPPING CODE: Adhesives HTN 3506.91

 

Rail (RID)

  • CLASS – 3 Item 3(B) Symbol – FLAMMABLE LIQUID

 

Road (ADR)

  • CLASS – 3 Item 3(B) Kemler Plate – 33 (1203)

 

Air (ICAO)

  • CLASS – 3 Pack Group 2 Symbol – FLAMMABLE LIQUID

 

Passenger Aircraft

  • Maximum quantity per package: 5lt
  • U.N. packing instruction: 305
  • Transitional packaging Inst. No.: T300

Footer

As a “One-stop Insulation shop” Insulpro CC can offer insulation solutions across all temperature ranges and applications.

CONTACT US

Tel: 0118352127
Email: mail@insulpro.co.za
Address: 52 5th Street, Booysens Reserve, Johannesburg, 2091
Website: www.insulpro.co.za

EMAIL US

Submission JHB